Experimental Equipment

Head: Dr. Katharina Zähringer

Measurement Systems   Wind tunnel   Water channel  3D-printers  Flow channels   Combustion lab   Rheology lab         

Measurement Systems

The LSS has a variety of optical and classical measurement systems at its disposal. These allow for measurements at different temporal and spatial resolutions, depending on the application. Specifically, the following is available:

  • Tomographic Particle-Image-Velocimetry systems (High-Speed Tomo-PIV and Tomo-PIV):

    Three-dimensional (3D3C) velocity fields can be determined with tomographic PIV. To this end the measurement volume is illuminated as a whole and several cameras trace particle movement from different angles. The 3-D particle movement can then be calculated from these different viewpoints. Two different systems are available: (i) a high-spee system with 6 Phantom VEO 640L cameras with a frame rate of 1400 Hz at full resolution and a high-speed ND:YLF laser or pulsed LED panels for ilumination of the measurement volume; (ii) the second system consists of four sCMOS cameras with an image rate of 50 Hz and an Nd:YAG-laser, which can be run at 266 nm, 355 nm and 532 nm. This enables the use of fluorescent tracer particles and thus measurements in complex geometries in which too many reflections would otherwise occur.<

    high speed tomo piv MA 1
    High-speed Tomo-PIV in einer Blasensäule                                    Tomo-PIV in einem Wendelreaktor

     

  • High-speed measurement system for Laser-Induced Fluorescence (LIF), Particle Image Velocimetry (stereo-PIV) and Colour Particle Tracking Velocimetry (PTV):

    The system involves two high-speed cameras, intensifiers, a high-speed laser, and corresponding software for control and analysis. The two colour photography cameras can take up to 1102 images/s using the full resolution of 2016 2016 pixels and up to 4500 images/s using reduced resolution. The laser is an Nd:YLF laser with a maximum energy of 30 mJ/P and a maximum pulse rate of 2  kHz. Depending on the retained camera configuration, stereo-PIV is possible, allowing the acquisition of all velocity components (2D3C). Thanks to the colour information, a higher particle number density may be used for PTV measurements, compared to usual PTV methods, by employing different particle colours for different properties. It is thus possible to obtain very detailed flow information. Image intensifiers are used for LIF, allowing measurements of scalar quantities even at low light intensities.
    MA 2

    High-Speed-PIV in a bubble column

  • • Micro-Particle Image Velocimetry (µ-PIV):

    This system allows for the measurement of velocity fields (2D3C) in very small channels. For this, a stereo-microscope is equipped with two cameras and a laser is coupled through a light fibre. Lighting of the channel is then volumetric and the measurement plane is chosen by adjusting the depth of field of the camera/microscope-combination.
    PIV

    µ-PIV-System with stereo-microscope

  • Particle Image Velocimetry (PIV):

    This includes several systems to determine two-component velocity fields (2D/2C), as well as three-component fields (2D/3C) via stereo-PIV.
    MA 3

    Stereo-PIV in an aneurysm model

  • Particle Tracking Velocimetry (PTV):

    Additionally to the above mentioned High-Speed-PIV-PTV System three high-speed colour photography cameras (up to 500 images/s @ 1280 x 1024 px²) are available for stereoscopic imaging, as well as four halogen light heads or state of the art LED equipment for proper illumination for PTV measurements. In-house written software allows for 3-D particle tracking in liquid and gaseous flow.
    MA 4

  • Laser-Induced Fluorescence (LIF):

    For gas-phase LIF, two intensified cameras, a dye laser and appropriate software are employed (see also „Combustion lab“). In the liquid phase tracer LIF is used to determine scalar quantities (e.g. concentration, mixing, temperature). In particular, 2-tracer-LIF is often used by our chair in difficult lighting situations (e.g. bubble shadows) or for the characterization of micro-mixing, since a dynamic background image can be generated. High-speed-LIF can be performed via the above mentioned High-Speed system, which also includes an image intensifier.
    MA 5

  • Laser-Doppler-Anemometry and Phase-Doppler-Anemometry:

    Several systems for one- and two-component measurements in single- and two-phase flow are available. These are equipped with different lasers, e.g. DPSS-Laser, Ar+-Laser, and Nd:Yag-Laser.
    MA 6

    LDA measurement results of the two-phase flow in a diffusor-like channel.

  • Shadowgraphy:

    This allows for the determination of equivalent diameters of small particles or droplets down to a size of 5 µm. It is also very useful for the examination of coalescence phenomena. For this purpose, a laser light sheet is used as light source together with a camera-mounted microscope lens. When pulsed lasers are used, velocity determination is also possible.
    MA 7    25mps_50_200_220_28

    Analyse von Tropfenkollision und -koaleszenz im Windkanal mittels Shadowgraphie

  • Constant-temperature-anemometry:

    Different hot-wire anemometry systems for velocity determination are accessible and can be utilized in the wind tunnel, for example.

Wind-tunnel

Fully computer-controlled, Göttingen-type, open or closed test-section for single-phase (pure air) flow or two-phase (air/liquid) mixtures (mostly air/water). Different spray injection heads are mounted upstream of the test section for this purpose. Test section dimensions (H x W x L open/closed): 500 x 600 x 1100/1500 mm3. Three of the closed test section walls are optically transparent (400/450 x 500 mm3) for optical measurements. Flow velocity: ~0.3 to above 50 m/s; turbulence intensity: below 0.5%. Spray properties: dependent upon the spray injection heads used, Sauter diameter around 50 micrometers, flow-rate 50 l/h, for example.


MA 8

Wind-tunnel with open test-section (Download brochure)

Water channel

The open, closed-loop hydraulic channel has a maximum flow rate of 575 l/s (2100 m³/h). The dimensions are 10 m x 1.2 m x 0.8 m (L x W x H) with a reference fill level of 0.6 m. The maximum velocity at the maximum cross-section (a.2 x 0.6 m2) is 0.8 m/s. The channel is equipped with a computer-controlled traversing system with a pathway of (X/Y/Z in mm) 2000 x1200 x 250 and a micro-controlled fill level and flow velocity regulation.<
MA 9  wasserraeder_IMG_7851heatmap_nomirror_with_wheel

3D-printers

Two different 3D printers are available in the group for fast prototyping: 1) Raise3D Pro2, a dual-extruder FDM printer (Fused-Deposition-Modeling) of industrial quality, with an intermediate-size printing volume (280mm x 305mm x 300mm); it is used for very fast and cost-efficient printing, and can provide very different properties depending on the employed material; 2) Formlabs Form3L, a large (335mm x 200mm x 300mm) SLA printer (Stereolithography); it is used for complex, high-quality printing with excellent surface description and a resolution better than 25 µm.

3D Drucker

 

Flow channels

Different open-loop and open-channel installations for one-phase (gas or liquid) and two-phase flows are available. Examples are: 

  • Flow channel with elevated tank for non-pulsating flow applications,
  • Closed-loop installation for flow investigation in pumps, blowers, etc.
  • Open-loop channels for water and two-phase (air/water) applications

These are, depending on the application, equipped with inductive or thermal flow meters, controllable DC motors, electronic absolute or differential pressure and temperature measurement, and PC-based data acquisition.

 

Combustion lab

The combustion lab is equipped for the examination of gaseous combustion systems in small and medium model burners. For these studies, the following measurement systems are used:

  • Laser-Induced Fluorescence (LIF),
  • Raman and Rayleigh-Scattering,
  • possibly both simultaneously with Particle-Image-Velocimetry (PIV).

LIFAnlage2

CH-LIF-measurements in a counterflow (Rolon-) burner geometry.

Rheology lab

Various rotational rheometers and other equipment are available for investigating Newtonian and non-newtonian fluids and suspensions:

  • air-mounted research rheometer „Kinexus pro+“ by Malvern with cone-plate, plate-plate and circular orifice geometry for rotational and oscillatory measurements at 0-200°C
    MA 11
  • Capillary viscometer „Cavis 2“ by Raczek for measurements in low-viscosity liquids
  • portable rheometer „VT500“ by Haake
  • Rotational rheometer „CV20“ by Haake

Additionally, a MasterSizer by Malvern is on premise for particle size determination in liquids or dusts.

 

Last Modification: 22.07.2022 - Contact Person: Webmaster